openstack base #0

Supports: focal

Basic OpenStack Cloud

This bundle deploys a basic OpenStack Cloud (Victoria with Ceph Octopus) on Ubuntu 20.04 LTS (Focal), providing Dashboard, Compute, Network, Block Storage, Object Storage, Identity and Image services. See also: Stable Bundles.


This example bundle is designed to run on bare metal using Juju 2.x with MAAS (Metal-as-a-Service); you will need to have setup a MAAS deployment with a minimum of 3 physical servers prior to using this bundle.

Certain configuration options within the bundle may need to be adjusted prior to deployment to fit your particular set of hardware. For example, network device names and block device names can vary, and passwords should be yours.

For example, a section similar to this exists in the bundle.yaml file. The third "column" are the values to set. Some servers may not have eno2, they may have something like eth2 or some other network device name. This needs to be adjusted prior to deployment. The same principle holds for osd-devices. The third column is a whitelist of devices to use for Ceph OSDs. Adjust accordingly by editing bundle.yaml before deployment.

  openstack-origin:    &openstack-origin     distro
  data-port:           &data-port            br-ex:eno2
  worker-multiplier:   &worker-multiplier    0.25
  osd-devices:         &osd-devices          /dev/sdb /dev/vdb

Servers should have:

  • A minimum of 8GB of physical RAM.
  • Enough CPU cores to support your capacity requirements.
  • Two disks (identified by /dev/sda and /dev/sdb); the first is used by MAAS for the OS install, the second for Ceph storage.
  • Two cabled network ports on eno1 and eno2 (see below).

Servers should have two physical network ports cabled; the first is used for general communication between services in the Cloud, the second is used for 'public' network traffic to and from instances (North/South traffic) running within the Cloud.


  • 3 Nodes for Nova Compute and Ceph, with RabbitMQ, MySQL, Keystone, Glance, Neutron, OVN, Nova Cloud Controller, Ceph RADOS Gateway, Cinder and Horizon under LXC containers.

All physical servers (not LXC containers) will also have NTP installed and configured to keep time in sync.


With a Juju controller bootstrapped on a MAAS cloud with no network spaces defined, a basic non-HA cloud can be deployed with the following command:

juju deploy bundle.yaml

When network spaces exist in the MAAS cluster, it is necessary to clarify and define the network space(s) to which the charm applications will deploy. This can be done with an overlay bundle. An example overlay yaml file is provided, which most likely needs to be edited (before deployment) to represent the intended network spaces in the existing MAAS cluster. Example usage:

juju deploy bundle.yaml --overlay openstack-base-spaces-overlay.yaml

Issue certificates

This release uses Vault to provide certificates to supported services. This allows secure communications between the end user and the cloud services, as well as securing communication between the services in the cloud. Vault needs to be unsealed and equipped with a CA certificate before the configuration can be finalised and the cloud used. Failure to do so will leave the deployment with the following message (in juju status):

'ovsdb-*' incomplete, 'certificates' awaiting server certificate data

Refer to the Vault and Certificate lifecycle management sections of the OpenStack Charms Deployment Guide for details. Example steps are provided in the OpenStack high availability guide.


Nova Compute and Ceph services are designed to be horizontally scalable.

To horizontally scale Nova Compute:

juju add-unit nova-compute # Add one more unit
juju add-unit -n5 nova-compute # Add 5 more units

To horizontally scale Ceph:

juju add-unit ceph-osd # Add one more unit
juju add-unit -n50 ceph-osd # add 50 more units

Note: Ceph can be scaled alongside Nova Compute by adding units using the --to option:

juju add-unit --to <machine-id-of-compute-service> ceph-osd

Note: Other services in this bundle can be scaled in-conjunction with the hacluster charm to produce scalable, highly available services - that will be covered in a different bundle.

Ensuring it's working

To ensure your cloud is functioning correctly, download this bundle and then run through the following sections.

All commands are executed from within the expanded bundle.

Install OpenStack client tools

In order to configure and use your cloud, you'll need to install the appropriate client tools:

sudo snap install openstackclients

Accessing the cloud

Check that you can access your cloud from the command line:

source openrc
openstack catalog list

You should get a full listing of all services registered in the cloud which should include identity, compute, image and network.

Configuring an image

In order to run instances on your cloud, you'll need to upload an image to boot instances:

curl | \
    openstack image create --public --container-format=bare \
        --disk-format=qcow2 focal

Images for other architectures can be obtained from Ubuntu Cloud Images. Be sure to use the appropriate image for the cpu architecture.

Note: for ARM 64-bit (arm64) guests, you will also need to configure the image to boot in UEFI mode:

curl | \
    openstack image create --public --container-format=bare \
        --disk-format=qcow2 --property hw_firmware_type=uefi focal

Configure networking

For the purposes of a quick test, we'll setup an 'external' network and shared router ('provider-router') which will be used by all tenants for public access to instances:

for example (for a private cloud):

openstack network create --external --provider-network-type flat \
    --provider-physical-network physnet1 ext_net

openstack subnet create --subnet-range --no-dhcp \
    --gateway --network ext_net \
    --allocation-pool start=,end= ext

You'll need to adapt the parameters for the network configuration that eno2 on all the servers is connected to; in a public cloud deployment these ports would be connected to a publicly addressable part of the Internet.

We'll also need an 'internal' network for the admin user which instances are actually connected to:

openstack network create internal

openstack subnet create --network internal \
    --subnet-range \
    --dns-nameserver \

openstack router create provider-router

openstack router set --external-gateway ext_net provider-router

openstack router add subnet provider-router internal_subnet

Neutron provides a wide range of configuration options; see the OpenStack Neutron documentation for more details.

Configuring a flavor

Starting with the OpenStack Newton release, default flavors are no longer created at install time. You therefore need to create at least one machine type before you can boot an instance:

openstack flavor create --ram 2048 --disk 20 --ephemeral 20 m1.small

Booting an instance

First generate an SSH keypair so that you can access your instances once you've booted them:

mkdir -p ~/.ssh
touch ~/.ssh/id_rsa_cloud
chmod 600 ~/.ssh/id_rsa_cloud
openstack keypair create mykey > ~/.ssh/id_rsa_cloud

Note: you can also upload an existing public key to the cloud rather than generating a new one:

openstack keypair create --public-key ~/.ssh/ mykey

You can now boot an instance on your cloud:

openstack server create --image focal --flavor m1.small --key-name mykey \
    --network internal focal-test

Attaching a volume

First, create a 10G volume in cinder:

openstack volume create --size=10 <name-of-volume>

then attach it to the instance we just booted:

openstack server add volume focal-test <name-of-volume>

The attached volume will be accessible once you login to the instance (see below). It will need to be formatted and mounted!

Accessing your instance

In order to access the instance you just booted on the cloud, you'll need to assign a floating IP address to the instance:

FIP=$(openstack floating ip create -f value -c floating_ip_address ext_net)
openstack server add floating ip focal-test $FIP

and then allow access via SSH (and ping) - you only need to do these steps once:

PROJECT_ID=$(openstack project list -f value -c ID \
       --domain admin_domain)

SECGRP_ID=$(openstack security group list --project $PROJECT_ID \
    | awk '/default/{print$2}')

openstack security group rule create $SECGRP_ID \
    --protocol icmp --ingress --ethertype IPv4

openstack security group rule create $SECGRP_ID \
    --protocol icmp --ingress --ethertype IPv6

openstack security group rule create $SECGRP_ID \
    --protocol tcp --ingress --ethertype IPv4 --dst-port 22

openstack security group rule create $SECGRP_ID \
    --protocol tcp --ingress --ethertype IPv6 --dst-port 22

After running these commands you should be able to access the instance:

ssh ubuntu@$FIP

Logging in to the OpenStack Dashboard

First determine the IP address of the OpenStack Dashboard:

juju status openstack-dashboard

Type in the following URL in your web browser: https://DASHBOARD-IP/horizon/

To print your credentials:

source openrc
env | grep OS_

Enable a remote access protocol such as novnc (or spice) if you want to connect to VM consoles from within the dashboard:

juju config nova-cloud-controller console-access-protocol=novnc

What next?

Configuring and managing services on an OpenStack cloud is complex; take a look at the OpenStack Admin Guide for a complete reference on how to configure an OpenStack cloud for your requirements.

Bundle configuration